UP-828P programmer is a famous UP Series Universal Programmer. which can
flash chips memory. it will enable examiners the ability to acquire the
data from the flash memory chip. Top recommend programmer from China
market.
Recommended Features
NAND FLASH, SERIAL FLASH, MoviNAND,iNAND, eMMC...
New UP-828P Ultra fast universal programmer flash memory
from Nandrepair
EMMC 's read/write speeds can reach to 20MByte/sec;
110 pins universal driving, Support VCC of devices from 1.2V to 5V;
Review for UP828P Ultra programmer
The
UP-828P Series programmer is High-Speed Universal Programmer for flash
memory developer, UP-828P Ultra fast universal programmer will enable
examiners the ability to acquire the data from a variety of flash
memory, including: NAND FLASH, SERIAL FLASH, MoviNAND, iNAND, eMMC...
UP-828
Ultra programmer have to be updated to UP-828P, Pls note it, new
UP-828P need new programmer adapter, old programmer adapter can't be
used on new UP828P programmer
The UP-828P Programmer offers a
growing number of IC sockets and chip adapters, it supporting a growing
number of mobile device memory chips.
UP828P Universal Programmer features
1.
UP828 Universal Programmer supports the newest types of FLASH, NAND
FLASH, SERIAL FLASH, MoviNAND, iNAND , eMMC etc, in addition, the BOOT
area of iNAND, eMMC and MoviNAND can be read and written
2. The EMMC 's read/write speeds can reach to 20MByte/sec;
3.
UP828 Universal Programmer Support 48MHz read and write pulse, the
highest support speed of reading and writing close to the limits of
devices. Program + Verify one 1Gb NAND FLASH only in 34 seconds, program
+ Verify one 8Mb FLASH only in 4 secondsChip Model N25S80 S71PL064JB0
K9F1G08U0A KLM8G2FEJA
Programmer UP828 UP128 UP828 UP128 UP828 UP128 UP828
Program + Verify (S) 3.4+0.6 null 30.3+1.2 43.4+4.1 22.2+11.4 78.4+167 468.42+458.24
Type 8Mb SERIALFLASH 64Mb NOR FLASH 1Gb NAND FLASH 8GBytes moviNAND
4. 110 pins universal driving, Support VCC of devices from 1.2V to 5V;
5.
Auto-test short circuit or bad contact of devices, with intuitionist
graphics Real-time detection ofshort circuit or bad contacting of
devices, Guarantee the safety and quality of programming device;
6.
Program interface is simple, the device operation unified, different
devices configuration and set option use uniform window entrance;
especially designed for mass production compact interface, even
front-line workers can easily using it freely;
7. Simple operation.
Nand-repair Professional repair device's Blog
2018年12月25日星期二
2018年12月3日星期一
how to install renault clip on the Serbian or Croatian language?
Renault clip diagnostic software can support with multi-languages, as we know, Nandrepairstatement that CAN CLIP work no issues in multi languages (English, German, Brazil, Danish, Spanish, Finnish, French, Italian, Norwegian, Dutch, Portuguese, Romania, Swedish), but how we add a new language in Renault clip?
In Renualt CLIP program, the description has Serbian Croatian Russian….. etc languages, and there are the Serbian or Croatian language files on the disc
The solution is in XP, Control Panel, Region and Language options, Regio Format set to Croatian, Home Location set to Croatian, at Tab Administrative, set Current system locale to Croatia, restart your PC and try install and you will see you have now Croatian language for choosing at installation
If you have the next message: “The current clip language is not supported by this version of the CD. To install this CD you must first uninstall the current version.
End of processing.”
End of processing.”
The solution is- Try to make system restore before you tryed to install Clip
Than, make a region and language settings to Croatian and after that try to install, If you cant do that,install on language that it asks, probably EN, than uninstall, CHANGE REGIONAL SETTINGS to Croatian and than try again.
Than, make a region and language settings to Croatian and after that try to install, If you cant do that,install on language that it asks, probably EN, than uninstall, CHANGE REGIONAL SETTINGS to Croatian and than try again.
That is, just change your settings in your PC to local language. (Croation or Serbian)
Now, Renault can clip diagnostic interface can be used in English, German, Danish, Spanish, Finnish, French, Italian, Norwegian, Dutch, Portuguese, Romania, Swedish, Croation and Serbian.
2018年11月30日星期五
How to fix iPhone 6S Receiver no sound troubles?
have you met such troubles? Your iPhone suddenly has no sound. You
may restart the phone repeatedly, but it has no effect. Someone called
you, but you can’t hear any sound. This is a very angry thing. Don’t
worry, next, the Nandrepair will tell us a practical way, I believe
your phone will return to normal work soon!
The iPhone 6S receiver has no voice when it is in calling, we can’t hear the voice from another side, we can hear from each other when we turn on speaker on iPhone.
According to our repair experience, the iPhone receiver no sound, but the iPhone speaker can hear the voice, this problem is usually caused by iPhone receiver, receiver flex cable, receiver circuit or iPhone audio IC problems.
First we need to test the iPhone 6S. Power on iPhone 6S, go to Settings->Sounds & Haptics to test the ringtone, the ringtone voice tested is normal. Make a phone call to someone else, the receiver has no sound, but the speaker is normal.
Now, replace the receiver and flex cable, and then test the iPhone 6S, but the failure still exist.
Use digital multimeter to measure the diode data of receiver signal 1 pin and 3 pin that on the connector J3100, the data measured are normal.
Check iPhone schematic diagram via WUXINJI Dongle,
we know that the 1 pin and 3 pin of J3100 are through capacitor FL3153
and FL3154 to iPhone audio IC U3500, their diode data are normal, which
means the capacitor FL3153 and FL3154 are normal.
After
excluding the cause of the peripheral components,we start to check
U3500. Take out the iPhone motherboard, we found the U3500 has been
replaced before by other repair man, the several filter capacitors
around it has been removed, and there is a power supply IC of NFC also
has been removed.
Now, we need to fix iPhone receiver failure, directly replace the iPhone audio IC U3500. After replacement, connect iPhone 6S to the DC power supply, the trigger current jumps from 0 to 80mA, it’s been circulating like this.
The replacement IC has been soldered well, the iPhone CPU didn’t been blown by QUICK 861DW hot air rework station. Remove the iPhone audio IC, now the current is back to normal, so we confirmed that it’s the problem of the iPhone audio IC. Replace it with new iPhone audio IC, and then install the iPhone.
The iPhone is turning on smoothly, the iPhone receiver is working properly, and the iPhone speaker also works normally.
2018年11月28日星期三
iPhone 7 won't turn on, how to fix it?
it is very common that your iphone 7 won’t turn on, you have to
master the reason, that's mean why My iPhone Won’t Turn On? is software
crashed or the battery charger problem? even is the logic board dead?
today we will talk about the logic board is short-circuit on the iphone7
CPU, how to fix it?
First
use the iPhone open tool to remove the iPhone and disconnect the
battery, then connect the phone to the DC power supply, the current
reading of the ammeter jumps to 350 mA and then remains still, which is
an abnormality, indicating that the logic board is shorted.
Disconnect power and remove the logic board. Measure the capacitors around the power IC one by one. Except for C1823 all values are normal - 0 is displayed, which indicate a short circuit in C1823. Observe schematic with WUXINJI dongle, C1823 is the filter capacitor of PP1V8-SDRAM, which is directly connected to the CPU SDRAM.
Connect the logic board to the PCB bracket, use QUICK 861DW hot air rework station to heat shield cover, and then remove the CPU SDRAM with a CNC chip grinder. After grinding the chip, attach the logic board to the PCB holder and cleaned with PCB cleaner, and then the black adhesive is removed with graver scraper cutter. After that, apply BGA solder paste to the pads, and solder with a heat gun.
Connect the iPhone to a DC power source, then use tweezers to lead the pin 13 of the J4504 to ground to trigger system power. This time, the current read on digital multimeter is normal.
Assemble the logic board. Connect your iPhone to your computer, then turn off the volume and enter DFU mode, insert your SIM card and activate your phone.
After testing all the functions work well. Repair work completed successfully.
2018年11月26日星期一
iPhone 7 iTunes Error 4013, how to repair it?
iPhone 7 iTunes Error 4013 is very common for iphone7 users, some of our
customer ask how to solve this problem? or which tools can fixing these
errors, in this articles, Nandrepair will give you the best solutions.
What's is the iTunes Error 4013 error?
When you press the power key to start your iphone, it will be stuck in iTunes recovery mode, can not access the system
What's is the iTunes Error 4013 error?
When you press the power key to start your iphone, it will be stuck in iTunes recovery mode, can not access the system
connect it to the computer and recover through iTunes, the error 4013 occurs during the recovery process. The phone boots again.
nandrepair.com Fault Analysis
iTunes Error 4013 of iPhone 7 usually caused by pseudo soldering or damaged CPU. The error may be related to the power supply of the baseband PMU or NAND flash. Since CPU repair is very difficult, so we can check the power of the baseband PMU and NAND flash at first.
Connect the iPhone to the DPS DC power supply and measure the voltage of the baseband PMU C5623 and C5631. The result shows that the values of C5623 and C5631 are normal. So we judged that the power supply of the baseband PMU is normal too.
Fault Repair
Let’s pay attention to the NAND flash power supply, remove the black adhesive around the NAND flash with PPD861D Hot Air Rework Station. Test the voltages of the NAND flash C1701, C1721 and C1704 with digital multimeter. From the measured value, the power supply of NAND flash is also normal.
It seems that the NAND flash is not the problem. Let’s replace the PMU and see how it works. Use heat gun to disassemble the PMU from the substrate and then use soaked SANKI solder wire to weld wire reel.
Tip: Some chips are sealed to the pads with black adhesive, to avoid knocking pads on the board, be careful to operate. Then clean with a PCB cleaner.
Apply some Solder Flux Rosin Paste to the pad,and fix the new baseband PMU in place (note the direction). Then weld with hot air gun. After finished, wait for the logic board to cool for 5 minutes, then clean with PCB cleaner thoroughly.
Assembly and Test
So far, the entire fix process has been completed, install the logic board and display components. Connect to the battery and press the power button to turn on the power, and the iPhone stuckis in iTunes recovery mode. We need to connect it to the computer to recover it through iTunes. The phone can be recovered normally. When finished, the iPhone will restart automatically, and the fault have been resolved.
iTunes Error 4013 of iPhone 7 usually caused by pseudo soldering or damaged CPU. The error may be related to the power supply of the baseband PMU or NAND flash. Since CPU repair is very difficult, so we can check the power of the baseband PMU and NAND flash at first.
Connect the iPhone to the DPS DC power supply and measure the voltage of the baseband PMU C5623 and C5631. The result shows that the values of C5623 and C5631 are normal. So we judged that the power supply of the baseband PMU is normal too.
Fault Repair
Let’s pay attention to the NAND flash power supply, remove the black adhesive around the NAND flash with PPD861D Hot Air Rework Station. Test the voltages of the NAND flash C1701, C1721 and C1704 with digital multimeter. From the measured value, the power supply of NAND flash is also normal.
It seems that the NAND flash is not the problem. Let’s replace the PMU and see how it works. Use heat gun to disassemble the PMU from the substrate and then use soaked SANKI solder wire to weld wire reel.
Tip: Some chips are sealed to the pads with black adhesive, to avoid knocking pads on the board, be careful to operate. Then clean with a PCB cleaner.
Apply some Solder Flux Rosin Paste to the pad,and fix the new baseband PMU in place (note the direction). Then weld with hot air gun. After finished, wait for the logic board to cool for 5 minutes, then clean with PCB cleaner thoroughly.
Assembly and Test
So far, the entire fix process has been completed, install the logic board and display components. Connect to the battery and press the power button to turn on the power, and the iPhone stuckis in iTunes recovery mode. We need to connect it to the computer to recover it through iTunes. The phone can be recovered normally. When finished, the iPhone will restart automatically, and the fault have been resolved.
2018年11月12日星期一
What is JC PRO1000S?
if you are phone repairman, we guess that you are insterested this JC
pro1000, Maybe you will ask What is JC PRO1000S? you will get the answer
as follows:
JC PRO 1000S programmer is an 4.3-inch equipment with touch display Screen, FreeRTOS operation system, touch control home button, and it supports turn on /off, return function, internal original brand battery.The JC PRO1000S tool support Chinese / English Language, Online / offline model,also it supports software update and function update in the future.
The full set of JC PRO1000S programmer which including
iPhone battery test adapter, iPhone genuine data cable detection adapter, iPhone logic EEPROM IC and Baseband EEPROM IC repair adapter, iPhone NAND Flash chip adapter,etc.
The Latest Multifunctional JC PRO1000S Modules:
1. iPhone battery testing module (with test cable)
2. iPhone genuine data cable detection module
3. iPhone lightning headphones cable check module
4. iPhone eeprom IC Reading / Re-writing module(Support iPhone 4-6SP)
5. iPhone Baseband EEPROM IC Reading / Re-writing module (stay-in-place, don't need remove IC)(Support iPhone 4-5S)
6. iPhone 2-IN-1 Baseband EEPROM IC Reading / Re-writing module (stay-in-place, don't need remove IC) (Support iPhone 6-6p)
7. iPhone 2-IN-1 Logic EEPROM IC Reading / Re-writing module (stay-in-place, don't need remove IC) (Support iPhone 6s-6sp)
8. iPhone Logic and Baseband EEPROM IC Reading / Re-writing module (stay-in-place, don't need remove IC) (Support iPhone 7-7p)
9. iPhone Baseband chip (Qualcomm/ inter EEPROM IC)(Support iPhone 7/7p)
10. iPhone / iPad 32bit and 64bit NAND Flash Reading / Re-writing module
11. PCIE iPhone iPad NAND Reading / Re-writing module(Support iPhone 7 5SE 6S 6SP 7 7P iPad Pro)
12. iPad iCloud Unlock Non-Removal Adapter for JC Pro1000 (Support iPad 2 3 4)
13. PCIE iPhone NAND Reading / Re-writing module(Support iPhone 8 8/8P/X)
JC PRO 1000S programmer is an 4.3-inch equipment with touch display Screen, FreeRTOS operation system, touch control home button, and it supports turn on /off, return function, internal original brand battery.The JC PRO1000S tool support Chinese / English Language, Online / offline model,also it supports software update and function update in the future.
The full set of JC PRO1000S programmer which including
iPhone battery test adapter, iPhone genuine data cable detection adapter, iPhone logic EEPROM IC and Baseband EEPROM IC repair adapter, iPhone NAND Flash chip adapter,etc.
The Latest Multifunctional JC PRO1000S Modules:
1. iPhone battery testing module (with test cable)
2. iPhone genuine data cable detection module
3. iPhone lightning headphones cable check module
4. iPhone eeprom IC Reading / Re-writing module(Support iPhone 4-6SP)
5. iPhone Baseband EEPROM IC Reading / Re-writing module (stay-in-place, don't need remove IC)(Support iPhone 4-5S)
6. iPhone 2-IN-1 Baseband EEPROM IC Reading / Re-writing module (stay-in-place, don't need remove IC) (Support iPhone 6-6p)
7. iPhone 2-IN-1 Logic EEPROM IC Reading / Re-writing module (stay-in-place, don't need remove IC) (Support iPhone 6s-6sp)
8. iPhone Logic and Baseband EEPROM IC Reading / Re-writing module (stay-in-place, don't need remove IC) (Support iPhone 7-7p)
9. iPhone Baseband chip (Qualcomm/ inter EEPROM IC)(Support iPhone 7/7p)
10. iPhone / iPad 32bit and 64bit NAND Flash Reading / Re-writing module
11. PCIE iPhone iPad NAND Reading / Re-writing module(Support iPhone 7 5SE 6S 6SP 7 7P iPad Pro)
12. iPad iCloud Unlock Non-Removal Adapter for JC Pro1000 (Support iPad 2 3 4)
13. PCIE iPhone NAND Reading / Re-writing module(Support iPhone 8 8/8P/X)
2018年11月1日星期四
What's the solution of iPhone X not charging after dropped?
After testing, the iPhone X charge icon can display normally,but iPhone power percentage is getting less when it in charging, this is actually a not charge failure. According to our repair experience, for the dropped damaged iPhone, the L3340 and L3341 inductors of the iPhone charge IC are easy to empty weld and pin missing.
Connect iPhone charging cable to the iPhone X tail plug flex cable, and then test the cathode of iPhone battery by uni-t ut81b multimeter oscilloscope, no voltage was found, so we judge the fault is in the charging part. If you want to delve into it, we have to measure it hierarchically, the AP part as shown in picture.
The external conditions measured are normal, according to our experience, we suspect that the inductors are empty weld and pin missing. Use quick 861dw hot air rework and tweezers to remove the L330 and L3341 inductors, the pins of inductor are on the solder pad, it's like IPhone7, and the inductors are easy to empty weld and missing.
Put it under the microscope, and then replace the new inductors( note: if replace it with iPhone 6 inductors, you need to insulate it,otherwise, it's easy to short-circuit.)
Measure it by iPhone X logic board test fixture, the functions tested are normal. Connect iPhone with uni-t ut81b multimeter oscilloscope, the current all is normal, the fault has been repaired.
订阅:
博文 (Atom)