MJ ACT PRO iPhone Chip Repair Tool user manual

The latest MIJING ACT PRO iPhone chip repair tool is an efficient equipment that available for reading and writing datas on iPhone 4S/5G/5C/5S/6G/6S/6SP/SE/7G/7P models, repairing flash error 1.3.6.16.47.48.1669 and 3G/4G signal faults on 4S/5G/5S/5S models. Also, it can reset and repair PC BIOS. but do you know how to use MJ ACT PRO iPhone Chip Repair Tool?



Operation Guide

• Software Download
1. Contact seller or log in MIJING official website "www.fsmijing.com"
2. find "download" - "下载中心" click into the page
3. find "Mi Jing Cloud Software"- 米景云平台“ to download and install
4. Run the software and find " drivers" - "驱动安装“ in the menu
5. Choose " CH341(码片）”drivers to install and reset your computer



Chip Data writing and Reading Operation

1. Remove the motherboard baseband CPU you need to repair
2. Choose the " mainboard fixed chassis" for corresponding mainboard
3. Install mainboard on"mainboard fixed chassis" and fasten it by "fixed lever"
4. Run "Mi Jing Software" and click "Instrument" in menu - Chosse "Chip Repair Instrument" mode
5. Connect data cable to ACT PRO chip repair tool and computer USB port
7. Save the data file in computer after the reading is done.

(How to check the chip data is normal？It depends on whether you can read data on the left dialog box, otherwise, if there is blank, it means you get wrong operation or damaged chip" ）

Note:
For repairing flash error 1.3.6.16.47.48.1669 and 3G/4G signal faults on 4S/5G/5S/5S models, click the right side on software " 修复码片数据“ multioptions - Choose corresponding model repair options - Software will note the file you need to repair - Choose the chip file you saved in computer - Rename the repaired file and save in computer- Click "Erase Data" to erase chip data in mainboard before writing new one - Click " Open" to choose repaired file -  Click " Write" so you can write datas in mainboard chip - Remove the mainboard as soon as the writing process is done,  and connect computer flash IOS firmware to be in progress of repair operation.

8. Remove mainboard from ACT PRO chip repair tool and restall the new chip or mainboard you need to writing( Baseband CPU removing is essential)
9. Click the "Read" option, there is no need to save in computer
10. Click "Open" to choose the chip data saved in computer and click "Write"

Note:
For writing datas on iPhone 4S/5G/5C/5S models, you must erase data first, click " Erase Data" then you can wtrite data.
For other iPhone models : 6G/6P/SE/6S/6SP/7G/7P, this step can be passed.

11. Remove chip or mainboard, connect computer flash IOS firmware to test function then the whole process will be done successfullly!

How unlock iOS Passcode? use Passcode Brute-force tool?

when you meed iso passcode lock programmer, you maybe need an effective solution of iOS Passcode removal, by using these Passcode Brute-force tools for passcode brute-force attack. as a matter of fact, IP-Box V3 is an top tool for supporting passcode bruteforce cracking on the iPhone 7 and 7 Plus running iOS 10

If you wnat to repair your moible phone unlock, started to use special brute-force tools, Quite easy way to get and remove forgotten 4-digit / 6 digit passcode from iOS device, while the phone data remains intact. Brute-force tools can be used with any iPhone running iOS 10 or newer (later) version of iOS.


New apple Password Unlock Tool for iPhone 7 7plus, crack the forgotten screen password (4 or 6 digit) on iphone 7/7plus iSO 11/10, one unlocker can working with 3pcs iphone (7/7p) at together.

Please keep in mind that this is a time consuming method.  and can't crack the passcode in fast speed

Built on the success of the original IP-Box, the new IP-Box V3 now supports passcode bruteforce cracking on the iPhone 7 and 7 Plus running iOS 10, This method will keep all data intact once the passcode has been cracked, but can take long amounts of time depending on the length of the pass code.t this is a time consuming method.  and can't crack the passcode in fast speed

Brute-force tools comparison table:

Brand	iOS 7.0.0 - 7.1.2	iOS 8.0 - 8.1	Display (to read out the unlock code)	Sound signal notification about unlock	Phone charging	Standalone	Software	Manual
IP-BOX (iOS 7)	+	+ (adapter required)	+	+	+/- (Depends on the package content)	PC required	+	-
MFC Dongle	+	+ (adapter required)	-	-	+/- (Depends on the package content)	PC required	+	+
Miracle Black Box	+	-	+	+	+	+	-	-
IP-BOX 3 (iOS 10.**)	+	+(adapter required)	-	-	+	PC required	+

Forgot iphone 7 / 7plus Screen Passcode? How to Unlock It?

IP-BOX V3 is for  the iphone 7/7P/6s/6/5S/5 Screen Passcode unlock tool, ,  iphone 7 / 7plus Screen Passcode unlock tester is an intelligent tool which can unlock three iphone devices at same time, no need for phone disassembly

All intelligent phone passcode unlock tools, no need to disassemble the iPhone, it can unlock three iPhone simultaneously with one unlock tool, and it works independently and non-interference with each other, 100% for unlock 4 digit password, 80% for unlock 6 digit password, it search can search 20000 common passwords, unlock iPhone 7/7P tools sets windows PE System automatic Recognition and Optical technology of millisecond 0 error in one, about 40 seconds for unlock simple 6 digit password, Weak password less than 20,000 groups

Remark: This Password Unlock tool is only for testing and study, Otherwise accept the consequences by yourself if violate the state laws in your country, just sell to Cell phone repair service shop, it is the professional-grade iPhone 7/7 Plus Password unlock tool.

Client software download:

https://drive.google.com/file/d/0BzMEvK0bAD0edXhjSVBKcnlKVFE/view?usp=sharing

How to Access iSO bug:

https://youtu.be/-Wq_C1098V4

How to connect the cables

https://www.youtube.com/watch?v=03HhsMGJCs0

Pre-defined password and user demo video:

https://www.youtube.com/watch?v=9vroIcRaa3I 

Ten steps To fix the Iphone 7/7P Home Button

when you Iphone 7/7P Home Button is not working, how can we do? when your home button failures to respond when you press on it, thats mean your iphone home button have some trouble and need it to repair. if in this situation, nandrepair  think this article might hlep you that provide with a fast way to get rid of the trouble of home button or named home/Touch ID sensor assembly.

1. Power off your iPhone before disassembly.
2. Dismantle the display assembly. Opening the iPhone’s display will compromise its waterproof seals. Take extra care not to expose your iPhone to liquid damage after completing your repair. As for the way of dismantling the display assembly，you can search through the internet or visit here for help.
3. Remove the four Y000 screws securing the bracket over the home/Touch ID sensor: One 1.1 mm screw; three 1.3 mm screws.
4. Remove the bracket that secures the home/Touch ID sensor.
5. Lift the home button connector to the right to disconnect it from its socket on the interconnect cable.
6. Gently move the home button interconnect cable out of the way of the home button cable. Don’t try to detach the press connector completely—simply lift it up so that it is out of the way when removing the home/Touch ID sensor cable.
7. Flip the display assembly over, and apply a warm iOpener to the home/Touch ID sensor area for about 90 seconds. This will also help soften the adhesive holding the delicate sensor cable in place. A hot Air gun or hair dryer proved to be much more convenient and is a time savior. You can heat more and the glue becomes more fluid make the next steps with the opening picks much easier.
8. Use an opening tool pick to gently separate the adhesive holding the home/Touch ID sensor cable to the back side of the display panel.
9. Remove the old home/Touch ID sensor assembly.
10. Reinstall the new one in reverse order.
Replacing home button is a relatively complex operation requiring your patience and carefulness, and what is worth noting is that in most cases replacing the sensor with a new one will cause the loss of fingerprint sensor functions, but if properly handled, it can be good as new, Touch ID and all.

IP-box V3 iPhone Passcode Unlock Tool for iPhone 7 / 7Plus

New IP-BOX V3 is professional iPhone Passcode cracking Tool, it is used to crack any forgotten 4 or 6 digit password on iPhone with iOS 11/10. The intelligent unlock tool can be available for three iphone devices at same time, no need for phone disassembly. The latest firmware R10-6000 Version not only supports English interface, but also support iphone 7/7plus iOS 11/10 and iOS 7.12 of iPhone 4 to 5S,  iPhone 6/6s function will be added in future.



100% rate for unlocking 4 bit password, and 80% rate for 6 bit password, the equipment will run less than 20 thousand groups common weak password to successfully unlock password. It adopts windows PE, automatic system identification + optical technology to achieve millisecond zero error. For 6 bit weak password, the equipment runs more than 40 seconds for one group, less than 20 thousand group for weak password.

Just simply attach the device to your iPhone,  it will give you the passcode in some hours. You will then have full access to your iPhone, and all user data remains intact.




Please note the following tips when you using the device!!

1. When unlocking the iOS device, please keep the battery work, choose the Save Data option when Re-Store the iPhone by Re-Flash software.
2. Please choose the special Password by the software,  don't scan the password from 000000 to 999999, it will take very long time. And choose "delete" the firmcache file when re-store the iPhone.


IP-Box V3 Update Firmware (Software)

https://drive.google.com/file/d/0BzMEvK0bAD0ed3NxNzRNZlVYblU/view?usp=sharing



Software SETTING: 

Stop while the brightness changes 150
Each time interval bit (ms) 40
Each group of data interval (ms) 300    

XTUNER T1 Heavy Duty Scanner Diagnostic CM2150C Test FeedBack:

XTUNER T1 Heavy Duty Scanner test report. XTUNER T1 confirmed to work fine with Cummins CM2150C. XTUNER T1 Heavy Duty Scanner Diagnostic CM2150C Test FeedBack of Cummins truck CM2150C.

XTUNER T1 Heavy Duty Scanner XTUNER T1 HD Trucks Tool


Test purpose:

To confirm the functionality of Xtuner T1, check it’s working or not

Engine to test:

Cummins truck CM2150C

Scanner for the test:

Xtuner T1 truck

Tested functions:

Basic diagnosis (incl. Read/ clear faults, read data stream)

Activation test

Maintenance oil reset

Communication method in the test:

Obdii connection to the vehicle

WIFI connection to the PC and scanner

Test results:

Read/ clear faults......OK

Read data stream......OK

Activation test......OK

Maintenance oil reset......OK

Photos attached ...

XTUNER T1 Heavy Duty Scanner Diagnostic CM2150C Test FeedBack:

XTUNER T1 Heavy Duty Scanner test report. XTUNER T1 confirmed to work fine with Cummins CM2150C. XTUNER T1 Heavy Duty Scanner Diagnostic CM2150C Test FeedBack of Cummins truck CM2150C.

XTUNER T1 Heavy Duty Scanner XTUNER T1 HD Trucks Tool


Test purpose:

To confirm the functionality of Xtuner T1, check it’s working or not

Engine to test:

Cummins truck CM2150C

Scanner for the test:

Xtuner T1 truck

Tested functions:

Basic diagnosis (incl. Read/ clear faults, read data stream)

Activation test

Maintenance oil reset

Communication method in the test:

Obdii connection to the vehicle

WIFI connection to the PC and scanner

Test results:

Read/ clear faults......OK

Read data stream......OK

Activation test......OK

Maintenance oil reset......OK

Photos attached ...

New Arrived XTUNER T1 HD scanner XTUNER T1 Heavy Duty scanner

New launched XTUNER T1 HD scanner is now available. 2017 CablesMall New Item XTUNER T1 Heavy Duty scanner.  Xtuner T1 Auto Diagnostic Tools for Heavy Duty Trucks OBDII Tool.

XTUNER T1 Heavy Duty Scanner XTUNER T1 HD Trucks Tool
http://www.cablesmall.com/xtuner-t1-heavy-duty-scanner-xtuner-t1-hd-trucks-tool-p-664?zenid=9119ec35fb397abf2a74251f424f77bb

Electronic control system: BENDIX,  For CUMMINS

Standard OBD: Diesel OBD

Language: English Only

Xtuner T1 heavy-duty truck diagnostic tool HD truck scanner T1 Xtuner For multi-brand trucks

XTUNER T1 Features:

Extensive vehicle coverage for heavy-duty trucks.
Complete function capability including DTC, DTC freeze Info, Live data, Actuation test and Special function.
Support standard protocol J1939, J1708 and J1587.
Supply USB and WIFI connection for the VCI.
New software update on the internet.
Supply OBDII and other 10 connector.
Hardware architecture uses a new design with multiple protection, interference and stability.
Built-in overvoltage protection module is applied, in order to protect VCI and vehicle against accidental damage during checking.
Can work well and stably in high and low temperature environment.
The genuine Windows XP/7/8/10 operating systems allows for more stable performances, better compatibility and expandability.
Extremely easy-to-use with touch-screen operation and intuitive operation in the windows.

Where to Download XTUNER T1 HD V8.0 setup software? 

pls go to offcial site tdintel to download.

V2.5 MCT-500 Motorcycle Scan Tool new features:

MCT-500 Motorcycle Scan Tool Support K-line and CANBUS protocols. MCT500 Motorcycle Diagnsotic Tool Support Multi-Brand Motorcycles. MCT-500 Motorcycle Diagnostic Tool Replacement MCT200.

MCT-500 Motorcycle Scan Tool MCT500 Motorcycle Diagnsotic Tool

MCT500 Features:

Retrieve ECU information

Display live data stream

Read fault codes

Clear fault codes

Component test

Special Function，such as: oil reset, ISC reset, CO adjustment etc

Support view waveforms and the numerical curve changes in data steam.

MCT-500 Motocycle Scanner Support protocol:K-line and CANBUS protocols.

Cablesmall.com MCT 500 motor diagnostic tool Package: 

1PC x MCT-500 Main Unit

1PC x Main Test Cable

1PC x S-YM cable    

1PC x KY-MCO cable

1PC x SU-ZUKI-4PIN diagnostic cable

1PC x SU-ZUKI-6PIN diagnostic cable

1PC x P-GO diagnostic cable     

1PC x YA-MAHA diagnostic cable

1PC x Battery Clamp